I think that the form which is necessaries in SRX at Brembo-caliper wearing and which can attach a Caliper to the position if it may be allowed to wish so much nearer to a Front CB400T is lighter, and blur does not have it, either.
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.
I think that the form which is necessaries in SRX at Brembo-caliper wearing and which can attach a Caliper to the position if it may be allowed to wish so much nearer to a Front CB400T is lighter, and blur does not have it, either.
Fits: YAMAHA RZ350 81-82, YAMAHA XJ400ZE 80-82, YAMAHA XJ400ZS 80-82, YAMAHA XJ400Z 80-82, YAMAHA XJ400D 80-82
The caliper supports arrived very quickly all the way from Japan and the parts are of very high quality and fit perfectly. I will be fitting them to my UK 1980 Yamaha RD350LC (4L0) (also known as RZ350 in other countries) and I am very pleased with them. When I have fitted them I will attach another photo to this review.View Detail
Fits: YAMAHA RZ350 81-82, YAMAHA XJ400ZE 80-82, YAMAHA XJ400ZS 80-82, YAMAHA XJ400Z 80-82, YAMAHA XJ400D 80-82
I bought this because I went with brembo.
Of course, Exactly is attached, but you need to adjust the Shim to get Center.View Detail
This is a must have part for brembo installation.
I was not sure if it was Radial Mount or Axial Mount, but Axial is enough because it is OverQuality.
To install, just mount it on the Front fork and assemble the Caliper.
However, Aluminum Cut-out is not the same as "It's just the way it is. The feeling is ……
I think GCraft's Black Anodized Aluminum was more natural. (Sweat) 。View Detail
I used it in the field where I put brembo4POD on VT250 SPADA.
The one I received is the one with no problems.
The BoltQuantity is included with the Caliper.:There are 2pc.
Be sure to check the fastenedTorque properly.
I think the Pad on the inside diameter side of the disc is slightly sticking out.
I tried to put it as far out as I could, but it was still too far. (;^ω^) It's like
What does it look like in RS?
Didn't seem to be a problem on the test drive.
It may be that it is still a self-responsibility as long as the conformity is not indicated by Manufacturer.
I don't think you'll have to spend a lot of money on Ok.View Detail
Fits: KAWASAKI ZZR400 90-92, KAWASAKI ZXR400R 89-99, KAWASAKI ZXR400 89-99, KAWASAKI ZXR750R 91-96, KAWASAKI ZXR750 91-96
[How is it used?
Used in the OEMRotor300 era.
Silver, Compact and thick.
I didn't feel rigid anxiety.
Although the hole dimensions are provided, installation should be done with the Caliper on the side that it is going to move against the Fork outer during breaking and then bolt it in place.
Otherwise, the frictional force caused by the bolt tightening alone may cause the risk of gapping.
Was the one you received as per Image?
Yes
Was the installation difficult?
It's easy if you know the hang and the concept.
How was your experience with it?
OK
[Included Parts:were they on?
Yes, I was wondering if Shim was there.
[Was there anything that disappointed you?
NoneView Detail
Purchased for regular replacement.
If it were a little cheaper, I could get a stable replacement...View Detail
?attachment
The CBR650R is mounted at the same position angle as the NORMAL.
However, when the handlebar was cut to the Left lock, it interfered with the interior cover next to the Meter, so the interior cover was cut away.
I also purchased a 45° angled banjo adapter for the mesh hose to accommodate the tension of the mesh hose.
・NORMAL (Reserve integrated horizontal master) Impressions of
No complaints on public roads. Familiar feel and very easy to handle.
However, when the brake is set to "hard brake," the rate of increase in braking force relative to the input seems to decrease, and the brake becomes more forceful.
Radipon (Reserve separate body portrait master) Impressions of
It was totally different from what I expected, my expectation was that it would feel like a Rear brake…
It is really a mild and easy-to-handle radipon.
On public roads, it feels like NORMAL! I wonder if it's because NORMAL is the same NISSIN?
But I felt the radipon effect from Breaking a little stronger, and
It can be hung up to a hard brake without effort.
I felt trust that this could stop.View Detail
I purchased this for use with multiple Helmets. 。
Mount included with the BOLD.
Microphone and speaker are not included and must be purchased separately.View Detail
Grip that had been used for a long time was worn out and had to be replaced.
They are soft and dampen vibration.View Detail
[How is it used?
Used to lick Screw loose.
Was the one you received as per Image?
As per Image.
How was your experience with it?
When used on a strongly tightened Screw, it can be safely and securely removed.
The licked Screw was removed.
It is also useful for DIY Screw removal.
[Points to note]
When used on a licked Screw, it is best to beat it in with a Hammer before use.View Detail
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
Servicio al cliente
PEDIDOS
SOBRE NOSOTROS
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING