[Color de la luz]
6000 Kelvin : blanco
3000 Kelvin : color de la bola halógena
12v para las motocicletas
Sistema de iluminación DC
Aprobado las normas de inspección de vehículos (25.000 candelas)
Voltaje nominal : DC12V
consumo de energía : Hi-beam 20W/Lo-beam 20W
LED : CREE XLamp XP-L LEDs
*Por favor, instálelo correctamente según el manual de instrucciones. Si no se hace así, puede producirse un incendio o un mal funcionamiento.
*Antes de instalar la batería, asegúrese de que la llave está apagada desenchufando el cable terminal del lado negativo de la batería.
*No toque ni manche el chip LED. La acumulación de suciedad puede hacer que el chip del LED se queme por la acumulación de calor. Si la bombilla LED se daña por la suciedad después de quitar la tapa y el sello, no está cubierta por la garantía.
*Este es un instrumento de precisión, así que ten cuidado en su manejo. No lo dejes caer ni tires el cableado a la fuerza. El manejo erróneo puede causar mal funcionamiento, lesiones, quemaduras o accidentes que pongan en peligro la vida. Además, las chispas, el aislamiento defectuoso y los cortocircuitos pueden causar el fallo del producto o un incendio.
*No intente desmontar o modificar este producto de ninguna manera. Los productos desmontados o modificados no están cubiertos por la garantía.
*No mire directamente a la luz LED de los faros. No mire directamente a las luces LED de los faros.
*No derrame agua sobre el objetivo durante y justo después de que se apaguen las luces. Un cambio de temperatura repentino puede causar daños en la lente y en la bombilla LED. No toque la bombilla LED, la unidad de ventilador y la unidad de control en la parte trasera de la bombilla porque pueden calentarse.
*Este producto está diseñado sólo para motocicletas y no puede utilizarse en vehículos de cuatro ruedas.
*No lo cubra con papel o tela y no lo encienda cerca de objetos inflamables. Si no lo hace, puede causar fuego o sobrecalentamiento. No se encienda cerca de materiales inflamables como sprays y diluyentes inflamables, etc., que pueden causar fuego o un calentamiento anormal.
*No lo instale en el faro cuando esté encendido. Si no se hace así, se pueden producir daños o quemaduras.
*Este producto es impermeable para el uso diario, pero no es completamente impermeable. El acoplador de la unidad de control debe ser impermeabilizado con cinta de vinilo o cinta autofusible, o con calafateo. No moje la unidad de control con agua más de lo necesario.
*Evite el contacto directo con las lavadoras de alta presión cuando lave su coche.
*No deje caer ni dé un fuerte impacto a la bombilla LED o a la unidad de control. Puede causar daños en la bombilla LED o en la unidad de control, lo que no sólo acortará su vida, sino que también causará lesiones.
*Al montar las bombillas LED, asegúrese de aplicar la grasa de silicona suministrada a las zonas indicadas por la marca de grasa en el manual de instrucciones.
*No cubra el ventilador a prueba de agua. Asegúrate de que hay suficiente espacio para que el aire fluya detrás del ventilador.
*Usar un bloqueador de rosca para evitar que las partes roscadas se aflojen. Debes volver a apretar periódicamente las piezas roscadas.
*Se requiere experiencia y habilidad para su instalación. Por favor, hágalo instalar en una instalación de mantenimiento designada con un mecánico experto.
*Asegúrate de ajustar el eje óptico antes de usarlo. Puede obstruir la vista del tráfico que viene en dirección contraria y causar un accidente de tráfico. Para más información, consulte las normas de seguridad para vehículos de carretera.
*Es posible que la garantía del fabricante no sea aplicable a su vehículo como resultado de la instalación de este producto.
*Protech no se hace responsable de ningún daño o accidente causado por el uso de este producto. Protec no será responsable del costo de reparación de la cámara. No somos responsables del costo de la reparación.
*Si observa algún problema durante la instalación o el funcionamiento, por favor, póngase en contacto con su distribuidor o con el Departamento de Servicio de Protektec.
[Luminous color]
6000 Kelvin: white
3000 Kelvin: halogen bulb color
For 12V motorcycles
DC lighting method
Rated Voltage: DC12V
Power consumption: Hi beam 20W / Lo beam 20W
LED: CREE XLamp XP-L LEDs
*Install the product correctly according to the instruction manual.Improper installation may result in fire or equipment damage.
*Before installation, be sure to disconnect the terminal cord on the minus side of the battery and confirm that the key is OFF.
*Please do not touch or get the LED chip dirty.Dirt can cause the LED chip to burn due to heat being built-up.The LED bulb comes with an acrylic cap with a sealing seal.
*Please handle this product with care as it is a precision instrument.Do not drop the product or pull the wires forcibly.Improper handling may cause malfunction, injury, burns, or serious accidents that may result in death.In addition, sparks, poor insulation, or short-circuiting may cause a failure of the product or a fire in the vehicle.
*Do not disassemble or modify this product in any way.Products that have been disassembled or modified are not covered by warranty.
*Do not look directly at the LED light when it is on.It can cause visual impairment.
*Do not splash water on the lens while the light is on or immediately after it is turned off.Sudden temperature change may cause damage to the lens or LED bulb.In addition, please do not touch the LED bulb itself, the heat sink behind it, and the controller unit because they get to the high temperature.
*This product is for motorcycles only, so cannot be used on four-wheeled vehicles.
*Do not cover with paper or cloth and do not light near flammable materials.Failure to do so may result in fire or abnormal heating.Also, do not light near flammable items such as flammable spray, thinner, etc. or items that may ignite.
*Do not install to the headlight with the light on.Failure to do so may result in malfunction or burns.
*This product is waterproof for daily life, but it is not completely waterproof.Wrap the coupler coming out of the controller unit with vinyl tape or self-bonding tape, or use caulking agent to waterproof it.Avoid wetting the product with more water than necessary.
*When washing a vehicle with a high pressure washer, please do not let the high pressure wash directly hit this product.
*Please do not drop the LED bulb or controller unit, or give it a strong shock.It not only causes breakage, deterioration of performance and shortening of service life, but also causes injury.
*When assembling the LED bulb, be sure to apply the supplied silicon grease to the areas indicated by the grease marks in the instruction manual.
*Do not cover up the waterproof fan.Make sure that there is enough space behind the fan for the sucked air to flow.
*Use a thread locker to prevent loosening of the threaded part.Periodic retightening is also recommended.
*Installation requires expertise and skill.Please have it done at a designated maintenance facility with skilled mechanics.
*Please adjust the optical axis before use.It may obstruct the view of oncoming vehicles and cause traffic accidents.
*PROTEC is not responsible for any damage or accident caused by the use of this product.Protec will not be responsible for any labor charges or other costs incurred during repair.
*If you feel any abnormality during installation or use, please contact your dealer or PROTEC service department.