Tope del manillar
Product # 220180
199.16 MXN (1,813 JPY)
List price: 221.13 MXN Save 10%
+18 Punto web (1.97 MXN)
Product # 220180
199.16 MXN (1,813 JPY)
List price: 221.13 MXN Save 10%
+18 Punto web (1.97 MXN)
4.5 / 5
16 opiniones
I purchased a Kawasaki Zr-7S to convert to Separate Handlebars.
NORMAL is Handlebar Up Type, so if it is made into Separate Handlebars, it will surely hit the Tank.
A Handlebar Stopper is required to control the handlebar snap angle.
I also considered BEET, but the price was about twice as much, so I bought this one made by CF POSH again.
Although it is sold for the NSR50, it can also be used for Kawasaki vehicles.
We have used it on a GPZ1000RX before, so perhaps it could be used on a GPZ900R or ZrX1100/1200 area.
And of course, to the Zr-7's sibling, the ZEPHYR750.
Since the handlebar stopper adheres quite snugly, it may be difficult for vehicles with bent handlebar stoppers due to accidents, etc.
I was able to install it on my Zr-7S with no need to change the Bolt.
Since the handlebar angle is originally Large, it did not feel too uncomfortable when attached to the vehicle.
I would rather restrict it more.
Since there is some room in the thickness of the part in contact with the Stem side, it may be possible to set up a Tap around M4 and make it adjustable.
Oh, of course, Handlebar Lock will be disabled.View Detail
[How is it used?
I bought this bolt to prevent the cowl from interfering with the handlebar on my Ninja 400. The supplied bolt is not long enough so I bought a 55mm bolt and installed it.
Was the installation difficult?
It was difficult to tighten the machine because it was working in a secluded place, but I was able to install it in about 10 minutes.
How was your experience with it?
The handlebar angle is now smaller and the Separate Handlebars of Other Brand Products no longer interfere with the Cowl or Tank. It's not as easy to turn as it used to be.
Handlebar Lock will not be available.
Ninja 400 is cheaper than Ninja 400, so I think this is better.
[ITEMS TO BUY TOGETHER
55-60mmBoltView Detail
I bought this for my TZM50 but I couldn't install it.
It is a spec. that fits into the NORMAL Handlebar Stopper welded to the frame.
The width of the groove is insufficient for the thickness of the Handlebar Stopper of NORMAL to the width of Large.View Detail
I use it because I'm afraid of getting my hand caught in the Handlebar.View Detail
I think this is a standard product of Handlebar Stopper.
I use it on my NSRmini and KX65.
Both of them can be installed without any processing.
It is better to check it once in a while that the screw loosens rarely.View Detail
To continue viewing this product on Japan domestic webike (in Japanese), press "Go to Japan Domestic".
Notification
Por favor, seleccione la opción antes de añadir a su carrito.
Servicio al cliente
PEDIDOS
SOBRE NOSOTROS
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING
* The BEST and MUST store to find Japanese parts.
* Register now for amazing deals and other special offers!
* Over 800,000 listed items. It's hard NOT to find your parts.
Congratulations! Your new account has been successfully created! You can now take advantage of member privileges to enhance your online
shopping experience with us. If you have ANY questions about the
operation of this online shop, please email Webike through CONTACT US.
A confirmation has been sent to the provided email address. If you
have not received it within the hour, please contact us.