- Encaja:
- HONDA Grom MSX125 *Early model only
About quality and texture it's very neat and amazing
About the feeling of use It gets a little messy because it has to be processed and installed
Products to buy together Bolt, nut, cable tie
Diffi...Lee mas - Encaja:
- HONDA GROM 16-21
About quality and texture: I am happy with the quality and design of this steel rear rack finished in a black powder coating.
About the feeling of use: I do not use the rear rack often to carry ite...Lee mas - Encaja:
- HONDA Grom MSX125 JC61(1st half)
Unlike the OEM STAND, I am satisfied with the Large change due to the quality and ease of installation.According to the other imprements, the sensor of STAND needed to be adjusted by Washeretc. when i...Lee mas - Encaja:
- HONDA GROM MSX125
- HONDA
Rough finish
must consider bracket position.
It cause fin broke in by front fender.
but cheap price, fine stuff
it make forgive all.Lee mas - Encaja:
- HONDA Grom MSX125 Early model only
The year should be correct, but I can't install it at all.The Pitch of the Screw does not match the Engine side at all.GarbageLee mas - Encaja:
- HONDA GROM MSX125
- HONDA
The price is much lower than other companies' products, and the cost is the best.The construction of the product is solid, and the Red Anodized is even.Installation is also OEM Caliper supportBoltQuan...Lee mas - Encaja:
- HONDA GROM 16-21
- HONDA GROM 16-21
It's a good dress-up.My GROM has a 6cm long Swing Arm, so when I use the Fender Eliminator, mud splashes fly to the back of the Helmet.With this Rear Fender, mud splashing is almost Guard.However, bec...Lee mas - Encaja:
- HONDA GROM MSX125
- HONDA
I bought it for Dress-upCustom and Front fork torsional strengthening, but…Think about the front fork Strokes, and install it a little higher than the middle (Grom is soft, and often Bottom, right?)Af...Lee mas - Encaja:
- HONDA Grom MSX125 Early model only
There are a lot of products like this out there, but if you Match things to the Grom from the previous year... (Personal) I thinkIt's not a little too Slant, but it's cool.Lee mas - Encaja:
- HONDA GROM MSX125
- HONDA
Price, looks cosmetically good, Converting the Chain to a 428 looks fine. I had a hard time finding the Bolt color when I dropped it during installation. (=PωP) noLee mas - Encaja:
- HONDA Grom MSX125 Early model only
I used it on a 2013 Grom.Since I could not fix the License Plate Light in a good position, I lowered the Number a little with an additional bracket that I prepared separately and used it.It's well mad...Lee mas - Encaja:
- HONDA GROM 16-21
- HONDA GROM 16-21
I bought it because of the cost and the design, but the accuracy is so bad that it takes a long time to install and the Swing Arm is covered with scratches! (T_T) It's a waste of a great Design.Lee mas - Encaja:
- HONDA Grom MSX125 Early model only
I didn't know how to install it and replaced it by handIn the end, I removed all the side covers and did it one side at a timeQuantity:Pair (for Left and Right) The position of Screw and the procedure...Lee mas - Encaja:
- HONDA Grom MSX125 JC61(1st half)
Adjustable for MONKEY125 side stands switch I was looking for a stand and I found this product I bought this stand for Grom and installed it as it is almost compatible with MONKEY125 It looks good and...Lee mas - Encaja:
- HONDA Grom MSX125 Early model only
I replaced the Cowl when it fell over and crackedIt's much cheaper than having a complete set of OEMsFront Blinker is a mandatory Other Brand Product It's not easy to install if you don't put it on ag...Lee mas - Encaja:
- HONDA Grom MSX125 Early model only
It's not particularly difficult to install, but if you want to put a License Plate Light on it, it's pretty much the same thing Because it is narrow, it is offset by a few centimeters with an appropri...Lee mas - Encaja:
- HONDA GROM 16-21
The usage was mostly commuting to work and using it during the weekAfter a year and 10,000km metering, the rear box made an impossible moveWhen I checked, I found that Carrier had rupturedIt's not a w...Lee mas - Encaja:
- HONDA Grom MSX125 Early model only
I was worried that it would be cheap because of the Carbon Style, but the price is well worth it It's transcribed and self-satisfied enough! The installation is easy to remove and replace the inner Sc...Lee mas - Encaja:
- HONDA GROM MSX125
- HONDA
Overall, I thought it was cheaply made and worth the priceThe fin of the cooler was bent by the impact of the Ballpen's fall alone Is it this kind of thing?It's also the type that attaches downward, s...Lee mas - Encaja:
- HONDA Grom MSX125 JC61(1st half)
Although there was no problem with the installation of the Body, the mounting part of the Side stands switch was slightly different from the OEM, and it was necessary to adjust several Washers on the ...Lee mas
THE LARGEST
SHOP IN JAPAN
EXCLUSIVE COUPONS,
SALE, DEALS
FAST, RELIABLE
SHIPPING